Mix 1/4 cup salt, 1/4 cup borax, and 1/4 cup vinegar, then apply this paste to deep stains or heavily soiled sections of carpet. Allow the paste to sit on the carpet for several hours until it dries completely, then vacuum it away.
Baking soda is an excellent choice for cleaning heavily soiled carpet, as it absorbs mud, grease, and other unsightly residues. To use baking soda over your entire carpet, sprinkle it heavily along the surface and then grind or push it into the fibers using a fresh, dry sponge mop.
You can deep clean your carpets yourself using either wet or dry methods. To begin, make sure that you've already vacuumed and spot-treated your carpet. You can use a carpet cleaner that will scrub the dirt out of the fibers using water and a special solution.
Make a paste using equal parts vinegar and baking soda, and then mix the paste with warm water to create a paint-like consistency. Use an old toothbrush to scrub the paste onto the stain. Then, use warm water to clean the area with a cloth or sponge.
Pour a small amount of vinegar on the stain, followed by a sprinkle of baking soda. The vinegar works to saturate and soften up the offending mark while the baking soda does the lifting and deodorizing. Together, they bubble a little and work as a team to lift the stain to the surface.
Carpets made of wool, silk and other natural fibers can be rather delicate, and don't take too well to excessive exposure to very acidic products. Using vinegar on these types of carpet can permanently damage the fibers and ruin your carpet.
Carpets that still look dirty or have stains reappear after cleaning is a result of something called wicking. This is due to over wetting the carpet, the backing, and pad which causes them to return back to the surface once dry.
Sprinkle a layer of dry baking soda on the stain. Then, mix a cup of white vinegar with a cup of water and a few drops of dish soap in a spray bottle. The vinegar will foam when it hits the baking soda which will clean the stain. Leave it to sit for a few hours.
This can move along a lot quicker if you use vinegar and baking soda together, but baking soda on the stain by itself on the stain can be effective. Allow the baking soda to neutralise a stain overnight. 8 hours is beneficial but 12 hours is ideal.
Baking soda is the go-to solution for bringing your carpet back to life. Not only does it clean, it also kills bacteria, refreshes the pile and removes odours. Apply plenty of baking soda to completely cover your carpet then use a stiff brush to work it in, rubbing it in different directions.
“Baking soda's particles go deep down into the carpet, past the point you can't even see, all the way to the base to absorb and neutralize odors. The particles can then be lifted out with a vacuum, leaving you with a carpet that smells like, well, nothing!” says Dr.
With the right care and maintenance, most manufacturers say carpets can last up to 10 years, but the average lifespan is generally 3-5 years in the average household with 4 residents. After this time, thorough cleaning may no longer be effective because the carpet is too old, and it should be replaced.
After you get out your carpet cleaner, fill the clean tank to the line with hot (not boiling) tap water. Hot water does a better job cleaning than cold but, if you boil it, you run the risk of melting parts of your carpet cleaner. Add formula to the tank according to the bottle directions.
It's not unusual for DIY carpet cleaners to need eight or even 10 passes on a carpet before the water runs clear. This is especially true when: It has been a long time since your carpet was last deep-cleaned.
You'll probably need to let it sit overnight, but the key is to wait until the vinegar has completely dried. As it dries, the smell of the vinegar should dissipate. Finally, you'll just need to vacuum up the baking soda. If there's more than a little left in the spot, you may want to scoop some of it up first.
Steps to take
Mix 2 cups of warm water with four tablespoons of vinegar. Spray the water and vinegar solution on the stain and leave to dissolve for 30 minutes. Use the piece of cloth to blot the area gently until the stain gets absorbed into the fabric.
The short answer is that you should not use vinegar for carpet cleaning. There is truth to the idea you can use vinegar as a natural disinfectant for cleaning but it cannot remove dirt or soil from a surface or from carpet.
Professional carpet cleaners, on the other hand, have the equipment, specialty products and know-how that will allow them to get deep under the carpet's surface. This will allow them to provide a deep clean that will remove or reduce most stains, regardless of how long they've been in your carpet.
Create a solution of one part distilled vinegar and three parts cold water. Spray it onto your carpet fairly liberally, and allow it a few minutes of contact time. Then take a microfibre cloth, and start gently blotting. Don't scrub, otherwise you could damage your carpet.