Difficulty: Intermediate to expert. Toilet installation requires plumbing knowledge and the right tools for the job. A DIYer who attempts toilet installation needs to have the knowledge and experience on how to troubleshoot any installation problems and avoid potential leaks and damage.
All you need are a few hours, a helper and the right tools and toilet parts for the job. Before you begin learning how to install a toilet, choose your new toilet and, if you aren't replacing an existing toilet, make sure you have plumbing ready for the new installation.
One-piece toilets can cost as low as $100 and as much as $5,000 for some models. Most cost between $250 and $600 with the average cost around $500. Two-piece toilets can cost as low as $100 with the most expensive toilets costing around $3,000. Most average around $100 to $300.
National Average:$371
According to Angi and HomeAdvisor, the cost to replace a toilet ranges from $224 to $532, with a national average of $371.
Make sure that the new toilet doesn't just have good water efficiency, but that the flushing power is also strong enough to deal with waste in a single flush. Otherwise, the cost savings you would expect from a low-flow toilet may be wasted with repeat flushes.
When you purchase a new toilet, it should come with most of the parts that you'll need. Check the box and make sure it includes brass closet bolts (to connect the toilet to the flange), and a gasket for connecting the tank to the base, a wax ring, a fill valve, flush valve and flapper.
In essence, that depends on your skill level and experience, plus the type of toilet you have. If you've done this before, it should be a piece of cake. However, if it's your first time, and depending on the complexity of the job, it could take anything from one to four hours on average.
Should I Replace My Old Toilet? While your old toilets may technically do their job, they're simply not as efficient as newer models. Not to mention if your old toilets start to show their age by cracking, leaking, or clogging, it's often best to consider toilet replacement rather than repair.
The general rule of thumb is that you should replace the toilet if the cost of repairs is more than half the cost of getting a new toilet. Sometimes, the issue is one big problem. Problems like a crack in your toilet bowl can be a major hassle, so they are almost never fixed.
Can I remove a toilet myself? Yes, this is a job that some people can do on their own. But it will be much easier to lift and move an old toilet with an extra set of hands. Decker points out that a one-piece toilet (one with the tank and bowl connected) can weigh as much as 120 pounds.
The bathroom fitters are unanimous—if you're looking for a high quality finish, with a better seal against water damage, then always tile the floor first.
For most toilets, a 20-year lifespan is the outer limit. A toilet may continue to work after this, but it will be at a higher risk of starting to leak and suffering from numerous clogs and other repair issues. Get ahead of the problem and replace a toilet that's 20 years or older.
Barring there are no other issues, to remove and replace a toilet should take a professional plumber about 30 minutes. If your question has to do with how much should it cost, most plumbers in Midwest charge between $100-$150. Most charge this based on a minimum 1 hour charge.
On average, most toilets will have a lifespan of between 10 and 15 years, even with regular use. The lifespan may vary depending on the toilet model and the wear and tear it experiences over the years. Most toilets will start to give you warning signs indicating the time for replacement is near.
Not every toilet requires the same size hole, and clearances also vary, but there is a standard size and placement that works for most models.
The Kohler pressure-assisted toilet range is one of the best-known ranges of powerful flush toilets. Many models incorporate specially engineered flushing mechanisms and use gravity to provide a more powerful flush using as little as 1.28 gallons of water per flush.
Champion 4 Toilet Meet the Champion 4, the undisputed leader in high performance toilets. With the industry's widest 2 3/8" trapway and 4" flush valve, it created a plunger free world for homeowners and virtually eliminated clogged toilet call backs for plumbers.
Make sure the toilet dimensions will fit your space. Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It's best to perform this measurement before you remove the old toilet.
The one-piece toilet also tends to be more durable than the two-piece since it's made of one solid portion of ceramic, with fewer exposed plumbing or flushing elements. Many people like this option for crowded bathrooms where space is at a premium.
Also, know that even if your toilet is a little old, it may still do the job. Older toilets do often suffer from inefficiency. Replacement saves money and water. Believe it or not, the federal government even has something to say about your toilet.