A
Whilst it may not be immediately obvious, when also pressed, the smaller, plastic button operates the smaller volume flush, perfect for most types of waste. However, if you require a longer, larger volume flush, simply press the main button without also pressing the smaller, plastic button.
The toilet has two buttons on the cistern rather than the single-flush one; one button delivers a lesser amount of water (eg. 3 litres) and the other a greater amount (eg. 6 litres). It also uses a larger 10 cm trapway in the bowl, allowing for water to come out faster and clear the bowl efficiently.
IT IS FOR WATER CONSERVATION: The larger lever is to flush out around 6 to 9 liters of water, whereas the smaller lever is to flush out around 3 to 4.5 liters of water. Clearly, the larger one is to flush solid waste and the smaller one is to flush liquid waste.
More Sanitary: It is much easier to spray some disinfectant on a button than to cover every inch of a lever. For this reason, a button flush toilet can be kept cleaner, making it healthier for your entire family. Modern: Eventually, a toilet with a lever flush might join the list of outdated bathroom elements.
Dual Flush Toilet Buttons & Plates
The first smaller button releases a small amount of water, or half-flush, into the bowl - usually around 3L - and is intended for less intensive flushing.
If the toilet doesn't flush completely unless you hold the handle down for the entire flush cycle, it's usually because the flapper is not fully lifting away from the flush valve. This problem is caused by too much slack in the lifting chain that connects the flush lever to the flapper.
The most common cause is a flush valve seal worn out, deformed, or unclean. Water may leak continuously if the flush valve seal is not adequately sealed. Another possibility is that the tank is constantly filled due to a broken fill valve.
Dual-Flush Toilets
High-efficiency dual-flush versions combine a 1.28 gallon flush for solid waste and a . 8- to 1-gallon flush for liquid waste. Two-stage flush system toilets use about 20 percent less water per year than conventional one-flush-only toilets, and many qualify for WaterSense certification.
Over time, flappers wear out, which allows water to continually drain from the tank. The result is not enough pressure released at flush to completely empty the contents of your toilet bowl. You can fix this problem by replacing the flapper. It is easy to do with any standard flapper purchased from a hardware store.
Select the appropriate button or turn the appropriate lever, based upon the type of waste you've eliminated. For liquid waste, select the half flush button or lever. For solid waste, select the full flush button or lever.
Dual flush toilets have two options for flushing: high volume and low volume. The toilet only uses water when it is needed, rather than wasting gallons of water every time. Dual flush toilets use almost half as much water as older toilets. That means less money on your water bill and more money in your pocket!
The half-flush float is positioned half way up the valve body and is operated by the half flush button above. Both the full-flush float and the half-flush float are connected to the seal below. They are not however connected to each other and lift the seal independently of each other.
One of the most common causes for a constantly running toilet is a leak in the bottom of the flush valve. This lifts up when you press the flush button to allow the water in the cistern to run into the toilet bowl.
Many tend to associate lower flow with lower flushing power. Not true. New technology and design advancements, such as pressure-assisted flushers and modifications to bowl contours allow high-efficiency toilets to flush better than first-generation low-flow toilets.
If your toilet is slow to fill, it might be due to one of four reasons: a clogged vent, a clogged drain, faulty plumbing, or a blocked pipe.
choosing a water-saving, low-flush or dual-flush version when buying a new toilet - low flush toilets use six litres of water per flush compared to nine or more litres for other toilets. fitting a variable flushing device to existing higher flush toilets - this will give you a choice of flush volumes to help save water.
Water level in a Toilet Bowl is determined by the height of the outlet of its internal P-Trap. When the water level in the bowl is too high, it is usually the drain pipes are clogged.
People should still flush their toilets at least once a day. "Things like to grow in urine and after a while the chlorine will inactivate in the toilet bowl water. It will being to bubble away and things will begin to grow. The odor will increase so it can get disgusting, smell bad and stain your toilet," he said.
The average household has about 5 flushes a day. An older toilet uses 7 gallons per flush, a newer one could be as low as 1.6 gallons per flush. If it is 7 gallons that is 12,775 gallons per year on flushes. At 67% that would eliminate 8,559 gallons of water usage per year in your household.