In such cases ProSeal 896
The surface must be sufficiently dry and firm enough to walk on without marking and there must not be any free water present. If the surface is more than 5 days old, a light acid wash and pressure clean are required prior to sealing.
The acid washing of concrete is a requirement after the concrete has cured sufficiently, in order to remove surface efflorescence and to open the pores before sealing. This will help the sealer to penetrate and result in a superior bond between the sealer and the surface.
The curing of the concrete and the drying of the acid stain are critical. For newly installed concrete, a minimum of 14 days of cure time is required, preferably 21 before an acid stain is applied. Once cured, you can use an acid stain. After the stain is applied, allow it to dry for at least 24 hours.
While you do not strictly need to seal your acid stained concrete, we strongly suggest doing so. Applying sealer will help maintain the appearance of your stained concrete. You can apply sealer once the stain has been neutralized, rinsed well and the surface is completely dry.
Wait at least 30 days before sealing a new concrete surface—whether indoors or out—so that it has time to completely cure first. For the best results, the concrete surface should be clean and dry. That means no rain should be in the week's forecast if you're working outdoors on a patio, bench, or sidewalk.
Sealing without cleaning first is a huge mistake that only a novice would make. However, getting out all of the dirt and grime along with stains is a must before permanently securing them onto the driveway's surface with a sealer.
Though new concrete may not always require a second coat of acid stain, older concrete does require two coats of stain for complete coverage. For a more diffuse look, spray the stain onto the surface without brushing.
You can use mops, water hoses, wet/dry vacs, and/or extremely soft bristle brooms to neutralize the stain and remove the residue. Neutralize with water and either baking soda, t.s.p., or ammonia and then final rinse twice with clean water only. We recommend using 12 to 16 ounces of ammonia per mop bucket.
Again, yes. You absolutely should. Concrete is a very porous material and sealing it makes all the difference when it comes to its maintenance and longevity. After pressure washing your concrete driveway, it is imperative that you wait until it is completely dry before sealing it.
Prep the driveway for sealing
The last step before applying a sealer is to thoroughly clean the driveway. Start with a push broom and sweep away the heaviest debris. Then use a garden hose, or better yet, a pressure washer to rinse the surface clean of all loose dirt, sand, and grit.
By sealing your concrete every 2-5 years, as recommended by experts, you should keep your floor in good shape, preventing cracks, pitting, and additional damage.
When the sealer is applied too heavily, the air displaced through the surface can't escape, and it forms a bubble in the sealer surface. Bubbling of a sealer can also occur if application is done in hot weather, or if the concrete is in direct sun.
You can seal existing concrete at any time and on multiple occasions. Sealing your old concrete can assist in restoring its appearance. For existing slabs, make sure to clean the surface before applying another sealer.
“You want it very clean, but it must also be very dry,” he says. “You don't want to seal wet concrete.” Applying sealer to wet concrete will cause problems, adds Sacco, as the sealer can fog up. Sacco also suggests that once the concrete is completely dry, avoid applying the sealer during the heat of the day.
The answer depends on the surface's square footage. For large surfaces such as commercial floors, a sprayer is faster and way more efficient. Finally, for small surfaces, such as garages or any other exterior surface, a paint roller or any other type of roller will do the trick. Rolling is a less expensive process.
Wait at least 24 hours.
If you experience any dew, accidental sprinkling of water or rain as the sealant dries, the sealant can become stained, cloudy, blotchy, or discolored and it will no longer be aesthetically pleasing. Simply don't seal your paver if there is even a remote chance of rain, fog, or a drizzle.
Acid-Based Stains
An acid-based stain costs between $0.20 and $0.40 per square foot on average or a total of $2 to $14.50 per square foot with labor. Acid-based stains chemically react with your concrete flooring, giving a natural appearance.
Durability. Acid-stained concrete doesn't wear out. The surface is inflammable and ultraviolet (UV) light-resistant. Unlike wood staining, when done properly, acid-stained concrete floors don't chip, peel, discolor, or fade.
How Long After Power Washing Before Sealing? For best results and to ensure the sealant lasts as long as possible, you should wait 24-48 hours to seal your driveway after cleaning it. This allows sufficient time for the surface to fully dry.
Sealcoating a new driveway too early may trap oils within the asphalt, resulting in a driveway that is too soft or flexible. Sealcoat your asphalt driveway when the temperature is 50–90 °F. Only apply a sealant when you have two consecutive days without rain.