If you choose to pause grouting and continue after, here are some tips to help the grout blend in nicely: Don't leave any excess grout, including the bits of extra grout on the edges. Make sure all of the grout is cleaned off (other than a bit of the filmy haze on the tile!)
What's more, if water or grit gets into the joints of the tile, it can lead to serious problems. At this point you may wonder if a complete re-grout is necessary or if it would be possible to simply put new grout over old grout. The answer is, yes, it is possible to put new grout over old grout.
But that does not happen until the mortar has set and holds the tile firmly in place. So, when the initial tile goes down, you should let the mortar set for a day before walking on your unfinished tile floor. After the mortar is set, your new tile flooring needs grout to complete the job.
ANSWER. ANSWER - It is possible to grout over existing grout if there is enough depth to do so. 1/8 inch depth may or may not be adequate depending on the type of grout used. A latex modified grout may work, but you have to properly clean the existing grout to ensure the new grout adequately bonds.
You can apply new grout right over the top of the old grout. To do this, all you need is a grout removal tool. Use the tool to strike out the old grout, making sure the depth is at least 2mm, which is about the thickness of two dimes stacked one on top of the other.
Grout is applied to fill gaps or as reinforcement for certain structures. Before wiping it, let it set for around 15 to 30 minutes. After that, you can soak a grout sponge in water to remove any excess.
The grout should be dug out a minimum of 3mm deep (preferably deeper) so that new grout can have a firm base and a larger surface area of the sides of the tiles to adhere to. Do not attempt to apply new grout over the damaged existing grout.
The humidity in the environment, and the temperature of the room will also affect the drying times. The shortest time after laying tile that you can grout is 24 hours. However, it is much better to wait at least 48 hours before grouting.
Once the grout has started to harden (20 to 30 minutes), begin sponging. Don't use just any sponge, especially one from the kitchen; choose a “hydrophilic” sponge. Make sure the sponge is damp, not wet, and sweep diagonally across the face of the tile and wipe the grout off the tile surface.
Tile tends to expand when the room temperature reaches a certain level. That is why you should never install tiles next to each other and always leave a small space between slates for the grout lines. That is where tile spacers can come in handy.
More videos on YouTube
We would be remiss to leave the topic of potential grout haze off the table. As go-to grout and tile care specialists, The Grout Medic truly wants what is best for your tile. Waiting too long to wipe grout could result in unsightly grout haze. Don't wait too long to wipe off grout!
If grouted too early for instance of adhesive that takes 24 hrs to dry the white grout may discolour because of the moisture still in the adhesive and it cant get out due to the grout.. so will discolour... Small tiled area, there's nothing wrong with using rapid set and grouting the same day.
Regrouting a shower is more cost-friendly than replacing shower tiles entirely. It's worth regrouting a shower that needs a little TLC because grout helps protect your bathroom from mold and mildew.
You can grout with your finger. First apply the grout with a float, then neaten the grout line by running your finger along the lines. Leave to harden off a little before wiping the excess grout from the tiles' surfaces. After you have wiped, check the lines and again use your finger to create a neat finish.
Make sure your tile surface is completely dry before you attempt to remove any haze. This typically takes about 24 hours. Consult your installation professional—or, if you DIY-ed it, your grout's packaging—for the exact amount of time. But do not wait more than 10 days to remove grout haze.
Dampen the substrate and tiles
The use of water is an important part of the entire installation process. Before grouting, use a clean sponge with potable water to dampen the substrate throughout the tile installation. Next, dampen the edges of the tiles with a light water spray bottle.
If you try adding new grout over your old grout, the new mixture will not properly adhere to the existing grout or tile edges, leaving your shower open to water damage.
When tile looks old and dingy, consider regrouting the tile instead of replacing it. Full tile replacement is messy and difficult. As long as the tile is in good shape, regrouting the tile can work wonders by making the entire installation look brand-new. All you need is a couple of special tools and some time.
Grout is a cement-based product mixed with chemicals, water, and in many cases sand. Portland cement based grouts are particularly porous. Porous grouts attract water, dirt, oils, etc. While the tile industry does not require sealing, it is always recommended, especially in wet or high-traffic areas.
Do I have to remove all old grout before regrouting? Yes and No. If the old grout is mouldy, cracked and discoloured you can invest in the best grout cleaner to see what the grout looks like after cleaning. If a clean makes little difference it makes sense to remove as much grout as possible.