Pour Hot Water into the Toilet When you see the symptoms of a nasty clog, the best option you have is to pour hot water into your toilet bowl. You can use the hottest setting from your faucet first. If you need to heat some in the microwave or the stovetop, you don't want it to reach boiling temperatures.
This can melt PVC piping and pipe seals, causing serious damage. In addition, using boiling water to clear a clogged toilet can melt the wax ring around the toilet, or even crack the porcelain bowl, leading to a pricey trip to your favorite hardware store.
Hot Water and Dish Soap
When the water is extremely hot, but not boiling, pour into the toilet carefully. Wait for 10-15 minutes while the dish soap and hot water soften the clog. Once you do so, the toilet will unclog and flush freely.
The toilet fills using cold water because using hot water would be a waste of energy and detrimental to the function.
Make your own drain cleaner by pouring one cup of baking soda and two cups of vinegar into the toilet and adding a half gallon of hot water. Dish soap can also help loosen some obstructions. When using either method, allow the solution to sit overnight and then flush the toilet to see if the obstruction has cleared.
Since the toilet only uses cold water, there is less cold water available to your shower when the toilet is filling. This causes the water in the shower to be warmer, because there is less cold water mixing with the hot water.
What Causes a Toilet to Gurgle? The cause of your toilet gurgling is a blocked line somewhere. A clog is creating negative air pressure, Instead of air flowing through the lines,the air pushes back and causes the gurgling sound. Sometimes, you'll also see the toilet water bubble.
Caustic Soda
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores.
Pouring boiling water is quite risky as it might lead to a steam burn or scalding. Another thing to keep in mind is what type of material you are pouring in into. If you have a porcelain sink, it is likely to crack due to the heat. All in all, pouring boiling water down your drain will only cause issues down the road.
Sometimes you can clear a clog in metal pipes by simply emptying a kettle of boiling water down the drain, a little at a time. You can pour the water down the drain without removing the shower drain cover. Do not pour boiling water down PVC pipes, which can be damaged by the heat.
The general rule of thumb is that hot boiling water can soften or even slightly melt the joints in your PVC pipes so YES, if you subject these types of pipes to high temperature water on a regular basis - they can be damaged, causing leaks and eventually requiring replacement.
Baking soda and vinegar – put one cup of baking soda into the blocked toilet and wait two minutes. Afterwards, slowly pour two cups of vinegar and wait a few minutes before flushing the toilet. Dish soap and water – put dish soap, then hot water into the toilet.
A partially clogged toilet can sometimes be cleared just by using hot water. The pressure produced by the hot water helps to push material blockages away, while the heat works to dissolve any fat or grease that may also have built up.
Here's the longer answer: Your shower and toilet most likely share a drain line and a vent stack (this setup is called wet venting, more on that later). If either the line or the stack has a clog or blockage, air is forced either up or down your toilet, making the gurgling noise you're hearing.
Gurgling Noises
The noise will become audible when you run the water or flush the toilet. This is a sign that the tank is full and needs to be pumped. The gurgling results from the septic tank being too full of solids and not being able to function properly.
Baking Soda And Hot Water
Pour about half of a cup of baking soda down the drain and then follow up with a pot of boiling water. Let it sit for an hour or two before you try flushing again. It might take several attempts, but this method has been known to work really well in unclogging slow draining toilets.
You may have hot water in your toilet because of a bad flapper in the toilet tank or a bad fill valve. When a toilet has a mixing valve (to prevent condensation), a little hot water is added to bring the temperature up. When this system is not functioning correctly, you can get a bowl full of hot water!
Background: Most toilets have mixing valves to prevent condensation, allowing some hot water to flow into the cold water line to warm it. When the water leaks in continuously, however, the hot water dominates the cold and you get a tankful of hot water.
If your toilet is slow to fill, it might be due to one of four reasons: a clogged vent, a clogged drain, faulty plumbing, or a blocked pipe.
Baking soda and vinegar is a marvelous cleaning agent, and when dumped into a clogged toilet, often will break up the clog without you having to do a thing. This is what you want to do: combine two cups hot water with two cups white vinegar.
It's pretty simple — just like they do on food particles that are stuck to your dishes in the sink, the combination of hot water and dish soap help to dissolve and break up whatever it may be that is lodged in the toilet, causing a clog. This handy tip is great should you find yourself in a pinch.
Yes, the heat can cause your water pipes to expand from the high degrees and the strain you place on the plumbing pipes.
You can use Drano® Clog Removers to unclog a kitchen sink, bathroom sink, shower or clogged bathtub, but DO NOT use them in toilets. For clogged or slow-running drains, apply the product and let it work 15 minutes, then flush with hot water. For tough problems, allow 30 minutes before flushing.