If the LED light strip you bought is too long, you need to cut off the extra part. The first thing you should do is measure the right length. If you accidentally cut the strip too short, your effort will be wasted.
The best way to shorten lights wired in series is to remove an entire series section of lights by cutting lights apart where there are only has two wires, with the lights unplugged. Then, simply cap each of the two cut wires with a wire connector.
LED strip lights are designed to be easy to cut apart with a pair of scissors. Each LED has a pair of copper dots at the end. As long as you cut between the dots, all of the LEDs will work. From there, you can connect the LEDs to a power source either through a quick connector or by soldering.
LED light strips are favored for their versatility and flexibility — particularly since they can be cut to fit different areas of your home. Whether you want to add extra illumination to your kitchen counters or a backlight for your TV, LED strips can be trimmed to fit your needs and space.
You can, but we wouldn't recommend it. By cutting an LED strip light anywhere other than the designated cutting point, you run the risk of damaging the components on the strip itself, as well as the circuit board. This may ultimately result in the strip light not working.
While it will depend on the brand you choose, most LED strips can be cut. Some will have a cutting line or scissor icon at each space where the lights can be safely cut without damaging the circuiting. These are generally earmarked by a pair of copper dots at the end of the LED.
You cannot cut just anywhere on your LED strip. Instead, you must follow the guides located on the strips that will tell you where you can cut them. The LED strips should have copper dots or ovals, typically located every three LEDs. These markers indicate cut points where you can make a cut in the strip.
LED Strip Lights are such a versatile product due to the fact that they can easily be cut on the given cut lines and connected at any point between the copper dots on the LED Strip Lights, cut lengths vary between products.
If you don't mind a little asymmetry, then don't sweat it! But if you do, you're probably wondering, “Can you cut string lights?” The short answer is: yes.
To lessen the amount of spotting which occurs within a standard profile, you could consider a strip that offers a higher amount of LEDs per metre, such as 240, although there will still be a tiny amount visible, again due to the depth.
To put it simply, well-manufactured LED lights are extremely long-lasting and can be left on 24 hours, 7 days a week. This is because, unlike conventional types of light, LEDs produce minimal amounts of heat, which means they are unlikely to overheat or set on fire.
When cutting LED Strip Light it is very important to cut only on the given cut line between the copper dots. Cutting through or before the copper dots will result in no electrical conductivity to the following section. Use a pair of sharp scissors to cut the LED Strip Light directly down the given cut line.
Yes, LED strip lights will work after they've been cut as long as you cut them along the designated lines. LED strips are made up of several individual circuits, so each cut line demarcates the end of one circuit and the start of a new one.
Vetco recommends, as a general rule, not to connect more than three complete strips end-to-end without adding in extra, higher gauge power wire or additional power supply units down the line.
Then, connect the positive wire of the second strip to the positive terminal of your power source and connect the negative wire of your first strip to the negative terminal of your power source. This will complete the circuit between your two sets of led lights and allow them to share a single power source.
We know that both LEDs and fluorescent lights can cause visual, headache and migraine symptoms. In addition to the high proportion of blue light wavelengths, these issues are likely a direct result of the rapid flicker they both emit.
Unlike incandescent light bulbs, LEDs don't produce light using heat. This is part of what makes them so energy efficient. The downside is that their components can be sensitive to overheating, which can cause them to burn out prematurely.
Providing your string lights are wired in parallel, then cutting the wire short is fine – the rest of the lights will still work. Most outdoor string lights are wired in parallel, but not all. If you cut your wire short, you'll need to protect the exposed wire at the cutting point.
With that being said, let's move forward and have a look at the answer to the most commonly asked question, “Are LED string lights dimmable?”, Yes, they are!
yes, you can, the rest of bulbs on the wire will still work.
To shorten this, push the cable through the lower hole making a large loop, then simply pull that loop back through the top hole.